Radiator Not Heating Up and How to Find the Cause
One radiator in the house is cold while every other one is too hot. You have turned the valve both ways, you have hit it with your palm, and somebody in the family has suggested bleeding it, which is the only piece of heating advice most...

One radiator in the house is cold while every other one is too hot. You have turned the valve both ways, you have hit it with your palm, and somebody in the family has suggested bleeding it, which is the only piece of heating advice most of us own. The room stays at 16 degrees and the boiler runs anyway, which is the part that costs money.
A cold radiator is one of the easiest faults in a house to diagnose, because it tells you where the problem is by which part of it stays cold. The metal is a map. Put your hand on it in four places and you have narrowed five possible causes down to one or two, usually in less time than it takes to find the bleed key.
Read the temperature pattern first
Turn the heating on and give it fifteen minutes, then touch the radiator at the top middle, the bottom middle, and both bottom corners where the pipes come in. Note what is warm. The pattern tells you most of what you need.
Cold at the top, warm at the bottom means air trapped in the upper part of the radiator. Air collects at the high point because it is lighter than water, and it stops the top third from filling. This is the one that bleeding actually fixes.
Warm at the top, cold at the bottom is the opposite problem, and bleeding will do nothing. That is sludge, which is iron oxide and debris that settles in the lowest part of the radiator and blocks the flow across the bottom. A radiator with a cold bottom third usually also feels heavier than its neighbours if you can rock it slightly on its brackets.
Cold all over, while other radiators heat normally, points at the valves. One of the two valves is closed, stuck, or the pin inside the thermostatic head has seized. This is the most common cause I have run into after a summer with the heating off.
Cold all over, with other radiators also lukewarm, is not a radiator problem at all. That is a system problem: pressure, the pump, or the boiler itself.
The stuck pin almost nobody checks
Thermostatic radiator valves have a small metal pin under the plastic head, around 10 millimetres across, that gets pushed down to close the valve. After a few months of sitting in one position, that pin can stick in the closed position. The head turns freely, the numbers change, and nothing happens inside.
Pull the plastic head off. There is usually a knurled collar you turn by hand, sometimes a small nut needing a 13 or 15 millimetre spanner. Underneath you will see the pin. Press it gently with a thumb or grip it with pliers and work it up and down a few millimetres. A stuck pin often releases with a faint click and a rush of water sound through the radiator within a minute.
I have fixed three cold radiators in two houses this way and spent nothing. A plumber doing the same job is usually a minimum call out charge, somewhere around 70 to 120 in most places. It is the first thing to check on a radiator that is cold everywhere while the rest of the house is warm.
The advice I disagree with: just bleed it
Bleeding is the universal suggestion, and it is right about one time in four. The other three times it is either useless or it makes things slightly worse.
Here is the problem. Every time you bleed a sealed system, pressure drops. On a combi boiler, the gauge needs to sit at roughly 1 to 1.5 bar when cold, and bleeding several radiators can pull it under 1, at which point the boiler locks out and you have turned one cold room into a cold house. If you do bleed, check the gauge afterwards and top up using the filling loop if your system has one.
The second problem is that repeated bleeding is a symptom, not a fix. If the same radiator fills with air every few weeks, air is getting in from somewhere, which is usually a small leak, a failing automatic air vent, or corrosion generating hydrogen gas inside the system. Bleeding that radiator forever is treating the alarm rather than the fire. Black water coming out of the bleed valve is the giveaway for corrosion.
So bleed when the pattern is cold at the top and warm at the bottom, and only then. Once you have done it twice in a season on the same radiator, the question changes from how to bleed it to why it keeps needing it.
A radiator you bleed every month is not a radiator problem. It is a system telling you something and being ignored.
A method that takes about forty minutes
Work in this order. Each step either fixes it or rules something out, and you need a bleed key, a cloth, a towel and a thermometer if you have one.
- Check the pressure gauge before you touch anything. Cold system, 1 to 1.5 bar. Below that, the pressure is the story and the radiator is a side effect.
- Run the heating for fifteen minutes and map the four touch points. Top middle, bottom middle, both corners. Write it down, because you will second guess yourself later.
- Open both valves fully. Thermostatic head to its highest number, and on the other end lift the plastic cap and open the lockshield valve with a spanner, counting the turns so you can put it back.
- Pull the thermostatic head and test the pin. If it does not move freely, work it until it does. Listen for water movement.
- Bleed only if the top was cold and the bottom warm. Quarter turn with the key, hold a cloth under it, close as soon as water appears rather than hisses. Recheck the pressure.
- If the bottom is cold, feel the weight and the water colour. Sludge needs the radiator flushing or the system power flushing, which is a job with a hose and two buckets or a job for a professional.
- If nothing changed and the far radiators are all weak, suspect balancing or the pump. Radiators furthest from the boiler often need their lockshield opened more than the nearest ones, which is what balancing means.
Step three catches more faults than any other, and it is the one people skip because the lockshield valve has a plastic cap on it and looks like it is not meant to be touched.
What the noises tell you
A radiator that gurgles like a kettle has air moving through it. A radiator that ticks as it warms is just metal expanding against its brackets, which is normal and harmless. Banging in the pipes when the heating starts or stops is water hammer, and that belongs to a different investigation, the one covered in the piece on knocking noises in walls at night.
Also check whether the room is the problem rather than the radiator. A room that never gets warm while its radiator is hot the whole way across is losing heat faster than the radiator can supply it, and the usual culprit is air movement rather than insulation. The incense stick method in tracing a cold draft at home finds that in an afternoon.
When to stop and call someone
Three signs mean put the tools down. Water dripping from a valve body or a radiator seam, because tightening it often makes it worse. Pressure that falls again within a few days of topping up, which means a leak somewhere in the system. And a boiler showing a fault code, which is not something to guess at.
Everything else on this list is a thumb, a cloth and forty minutes. The useful habit is to map the pattern before you do anything, because once you have bled a radiator and opened a valve, you have destroyed the evidence that would have told you what was wrong. More household puzzles of this kind are in the living section.
FAQ
Why is my radiator cold at the bottom but hot at the top?
Sludge settled in the bottom of the radiator is blocking flow. Bleeding will not help, because the trapped material is not air. The radiator needs flushing.
How often should I bleed my radiators?
Once a year at the start of the heating season is plenty. Needing it monthly means air is entering the system and that cause is worth finding.
Can I fix a stuck thermostatic valve myself?
Usually yes. Remove the plastic head and work the pin underneath up and down. If it will not move at all, the valve body needs replacing, which means draining that part of the system.
Why is only the last radiator in the house cold?
That is typically balancing. The radiators nearest the boiler are taking most of the flow, and the lockshield valves on those need closing slightly so the far one gets its share.
More in Living
Living
Buzzing Light Switch at Home and How to Find the Cause
There is a dimmer in my hallway that hums. Not at full brightness and not when it is off, only in a band somewhere between a...
Living
Gurgling Drains in the Bathroom and How to Find the Cause
The bath in my sister's house makes a noise like someone swallowing, but only when the kitchen sink empties two rooms away.
Living
A Sticking Door and How to Find the Real Cause
There is a bedroom door in a 1930s flat I used to rent that fought me every November.