A Sticking Door and How to Find the Real Cause
There is a bedroom door in a 1930s flat I used to rent that fought me every November. By the second week of the month you had to lift the handle and lean, and by March it swung freely again as if nothing had happened.

There is a bedroom door in a 1930s flat I used to rent that fought me every November. By the second week of the month you had to lift the handle and lean, and by March it swung freely again as if nothing had happened. I did what the internet told me and took a plane to the top corner. Three millimetres off, a satisfying curl of pine on the floor, a door that closed beautifully. Then came July, and a gap along the top edge wide enough to see the landing light through.
A door that sticks is one of the more honest objects in a house. It cannot tell you what is wrong, but it marks the spot, and the mark is specific enough to name the cause before you touch a single screw. The mistake almost everybody makes, me included, is removing material in the first week rather than reading the evidence and waiting.
Start with where it rubs
Close the door slowly and watch the gap all the way round. Then run a sheet of ordinary printer paper into the gap at six points: top left, top centre, top right, down the latch edge at handle height, bottom left, bottom right. Where the paper will not go, the door is touching. A standard gap is between 1.5 and 3 millimetres, which is roughly two sheets of paper, and anything the paper slides through freely is fine.
If you want the mark rather than the measurement, rub a stick of blackboard chalk along the whole closing edge of the door and shut it firmly once. The chalk transfers to the frame exactly where the contact is. It is the oldest trick in carpentry and it takes two minutes.
| Where it rubs | Most likely cause | First thing to do |
|---|---|---|
| Top corner on the latch side | Top hinge screws pulling out, so the door is hanging at a slight angle | Tighten or lengthen the top hinge screws before anything else |
| Bottom corner on the latch side | Bottom hinge loose, or the door has dropped on a worn hinge pin | Check the bottom hinge for play by lifting the handle while the door is open |
| Along the whole latch edge, evenly | Swelling from humidity, or a repaint that added thickness | Nothing yet. Log it for a season and count the paint layers |
| Top edge only, across the width | Seasonal swelling, worst in the damp months | Measure again in the opposite season before removing anything |
| Hinge side binding, door springs back | Hinges mortised too deep, or packed out unevenly | Add a thin card shim behind the shallow leaf, not a planer to the door |
| Catches the floor or the carpet | New flooring, a lifted threshold, or a sagging joist underneath | Check whether the floor moved rather than the door |
| Latch will not engage at all | Strike plate out of line by a millimetre or two | Move the strike plate, which is a ten minute job with a chisel |
The first two rows cover most cases I have come across. A door hangs on three or four small screws and all of its weight, maybe 20 to 35 kilograms for a solid internal door, pulls on them every time someone swings it shut.
The hinge fix nobody mentions
Open the door to ninety degrees and lift gently under the latch edge. If it moves even a millimetre or two, the hinges are the problem and the rest of this article is academic.
Look at the screws. Most internal doors arrive with 25 millimetre screws, which reach into the soft pine of the frame lining and nothing beyond it. After a few thousand slams the threads chew out their own holes and the hinge leaf starts to tilt. You can tighten those screws and they will feel firm for about a fortnight.
The proper repair is to replace one screw per hinge, the one closest to the frame edge, with a 70 or 75 millimetre screw that passes through the lining and bites into the structural timber behind it. That single change fixed the sticking door in my sister's house four years ago and it has not moved since. Use the same head type so it does not look like a repair.
If the hole is too far gone to hold anything, the old fix still works. Snap two or three wooden matchsticks or a short length of 6 millimetre dowel, coat them in wood glue, tap them into the hole, cut them flush, and leave it overnight. The screw then bites into fresh timber rather than sawdust. Cocktail sticks are too thin to be worth the effort.
Why planing it is usually the wrong answer
Search for a sticking door and the first answer will be to plane the edge. I have done it, it felt like competence, and it was the wrong move.
Timber moves across the grain with the moisture in the air, not along it. A 760 millimetre internal door can grow and shrink by two to four millimetres in width between a dry heated winter and a humid summer, which is the entire size of the gap you are working with. If you remove material at the point of maximum swelling, you have fitted the door to one month of the year.
Indoor humidity in a UK flat typically runs around 35 to 45 percent with the heating on and 55 to 70 percent in August with the windows open. That swing is the whole story in most sticking doors, and a hygrometer costs less than a plane blade.
So the rule I now follow: measure the gap, write the date and the humidity on a bit of masking tape stuck to the top of the door, and wait at least one season before cutting anything. If the door sticks in both seasons, it is a hanging problem or a frame problem and planing will not cure either. If it sticks in only one, you have a seasonal door, and seasonal doors are better treated by sealing the edges than by shrinking them.
That last part matters and gets skipped. An unpainted or unsealed top and bottom edge is where the door drinks. Two coats of the same paint or a clear sealer on those two edges slows the exchange considerably, and on the flat door I lived with it reduced the November tightness enough that I never needed the plane again. The same moisture logic that drives this shows up on glass as well, which is what condensation on windows every morning is really tracking.
When the door is talking about the building
Sometimes the door is not the subject of the sentence. It is reporting on the house.
Hold a spirit level against the hinge side of the frame and check it for plumb, then measure the two diagonals of the opening with a tape. If the two diagonal measurements differ by more than about 5 millimetres, the frame is racked rather than the door warped, and the sticking is a symptom of movement somewhere else.
Three things raise the stakes. A new diagonal crack above the door, running from the corner of the frame up toward the ceiling. Several doors in the same part of the house going stiff in the same few months. And a change that arrived suddenly rather than gradually, especially after a dry summer or new work next door. Any of those and I would stop fiddling with hinges and get a structural engineer to look, which in my experience costs somewhere between 300 and 600 pounds for a visit and a short written opinion.
Most of the time it is far duller than that. Doors in an old house are rarely square because the house is not square, and a frame that has been three millimetres out of true since 1952 is not news. What matters is whether it is moving now, which is why the date on the masking tape is worth more than any single measurement.
Houses leave this kind of evidence everywhere once you start looking. A noise log, a chalk mark, a paper gauge. The method in tracing a knocking noise in the walls at night works the same way, and so does listening to squeaky floorboards properly.
What to do this weekend
Chalk the edge, close the door once, and photograph the mark on the frame. Then lift the latch edge to test the hinges. Those two steps take under ten minutes and between them they settle which of the seven rows in the table you are in.
If it is the top hinge, buy a box of 75 millimetre screws in the matching head and fix it properly in half an hour. If it is swelling, put the masking tape label on, seal the top and bottom edges, and come back in six months with the plane only if the door has failed you twice. More of this sort of thing lives in the living section.
FAQ
Why does my door only stick in winter?
Dry heated air shrinks timber, so a winter sticking door is often a hinge or frame issue that cold weather exposes rather than a swelling problem. Swelling almost always shows up in the damp months instead, which is why the season you noticed it in is a genuine clue.
How much gap should there be around an internal door?
Between 1.5 and 3 millimetres on the top and sides, and about 6 to 10 millimetres at the bottom depending on your flooring and whether the room needs airflow for a vent or an extractor.
Can I fix a sticking door without taking it off?
Usually, yes. Hinge screws, shims behind a hinge leaf and strike plate adjustments are all done with the door hanging. Taking it down is only necessary for planing or for a hinge that has to be remortised.
Does sticking mean the house is subsiding?
Rarely on its own. It becomes worth taking seriously when several doors change in the same season, when a diagonal crack appears above the frame, or when the opening measures more than about 5 millimetres out of square across the diagonals.
More in Living
Living
Buzzing Light Switch at Home and How to Find the Cause
There is a dimmer in my hallway that hums. Not at full brightness and not when it is off, only in a band somewhere between a...
Living
Gurgling Drains in the Bathroom and How to Find the Cause
The bath in my sister's house makes a noise like someone swallowing, but only when the kitchen sink empties two rooms away.
Living
Radiator Not Heating Up and How to Find the Cause
One radiator in the house is cold while every other one is too hot.