Toilet Keeps Running and How to Find the Cause
You flushed ten minutes ago and the tank is still hissing, or worse, it goes quiet and then refills on its own at 3am with nobody near it.

You flushed ten minutes ago and the tank is still hissing, or worse, it goes quiet and then refills on its own at 3am with nobody near it. When a toilet keeps running like this, it is more than an irritation: a steady leak can waste 700 litres or more a day, enough to show up on your next water bill.
The good news is that a running toilet almost always has one of four causes, all inside the tank, and you can find which one in about 15 minutes without tools. Here is the order I check them in, from the most likely to the least.
How a toilet tank works in 30 seconds
Lift the tank lid and you will see two main parts. The fill valve, usually on the left, lets water in after a flush and shuts off when a float rises to a set level. The flush valve, in the centre, has a rubber flap or seal at the bottom that lifts when you press the handle and drops back to hold water in the tank. In the middle of the flush valve is a tall overflow tube that sends excess water into the bowl if the tank overfills.
A toilet keeps running when water escapes from the tank faster than it should, or when the fill valve never gets the signal to stop. Every cause below is a version of one of those two problems.
Test 1: is the water level too high?
Look at the overflow tube. If water is pouring into the top of it, the tank is overfilling, and the fill valve is the culprit. There is usually a line marked on the inside of the tank, or a mark on the overflow tube, showing where the water should stop. It should sit about 2 to 3 centimetres below the top of the tube.
To fix it, lower the float. On modern fill valves, there is a small adjustment screw or clip on the side of the valve; turn the screw anticlockwise or slide the clip down a few centimetres. On older ball float types, gently bend the float arm downward. Flush and watch the new level.
Test 2: the dye test for a leaking flapper
If the water level is fine, the most common cause by far is a worn flapper or seal letting water trickle into the bowl. You cannot always see this happen, so use a simple test:
- Put five to ten drops of food colouring in the tank. Do not flush.
- Wait 20 minutes.
- Look in the bowl. If coloured water has appeared, the flapper is leaking.
Flappers are made of rubber and harden or warp over three to five years, especially in areas with chlorinated or hard water. A replacement costs a few dollars and fits by clipping onto two pegs at the base of the overflow tube. Take the old one to the hardware shop so you get the right size, usually 5 or 7.5 centimetres.
Before replacing it, run a finger around the seat the flapper sits on. A ridge of limescale can stop even a new flapper sealing. Scrub it gently with a scouring pad.
Test 3: check the chain and handle
Push the handle and watch. If the chain is too short, it holds the flapper slightly open after every flush. If it is too long, the slack can get caught under the flapper and stop it closing. You want about 1 to 2 centimetres of slack when the flapper is closed.
A sticky handle can do the same thing, staying partly down after a flush. If the handle feels stiff, tighten the nut inside the tank. Note that it is threaded in reverse on many models, so turn it anticlockwise to tighten.
Test 4: a fill valve that will not shut off
If the water level is correct, the dye test is clean, and the chain is fine, but you still hear a hiss, the fill valve itself may be faulty. Grit can get caught in the valve seal, especially after plumbing work or a burst main nearby. Turn off the water at the stop valve behind the toilet, remove the cap from the top of the fill valve, and rinse the seal under the tap. If that does not help, replacement fill valves are universal and cost about 10 to 20 dollars.
Why jiggling the handle is not a fix
The standard advice for a running toilet, passed down in most households, is to jiggle the handle until it stops. I would argue that this habit causes more harm than it prevents. Jiggling often does stop the noise, but only by forcing a worn flapper back onto its seat for a few hours. The underlying leak continues, often silently, and people go months without noticing their water use has doubled.
Worse, constant jiggling stretches the chain and wears the handle mechanism, so a cheap flapper problem turns into a handle replacement too. If you find yourself jiggling more than once a week, run the dye test. It is a ten minute answer to a problem that will not go away by itself.
When a toilet keeps running for reasons outside the tank
Occasionally a toilet keeps running because of something outside it. Unusually high water pressure can push a fill valve past its shut-off point; if you also notice banging pipes or dripping taps elsewhere, that may be the issue. A slow, hidden leak elsewhere in the house can also make you think the toilet is the culprit when you hear water moving. For a structured way to rule that out, see our guide on tracking down a hidden water leak at home. And if the opposite problem shows up at one fixture, with a weak flow rather than a constant one, low water pressure at one tap walks through those causes.
A quick meter check settles it. Turn off every tap and appliance, note the reading on your water meter, wait 30 minutes, and check again. If the number has moved with the toilet's stop valve closed, the leak is somewhere else. For more step by step household detective work, browse the living section.
Frequently asked questions
Why does my toilet keep running after I flush?
The most common reasons are a worn flapper that does not seal, a chain that is too short or tangled, or a water level set too high so water spills into the overflow tube. Check them in that order. Most fixes take under 15 minutes and cost very little.
How much water does a running toilet waste?
A slow trickle can waste around 100 to 200 litres a day, while a constantly running toilet can waste 700 litres or more. Over a month, that can add noticeably to a water bill. A dye test will show you whether there is a silent leak.
Can I fix a running toilet myself?
Yes, in most cases. Replacing a flapper, adjusting a float or shortening a chain needs no tools and no plumbing experience. Call a plumber if the fill valve or the tank itself is cracked, or if the problem remains after you have checked all four causes.
More in Living
Living
Buzzing Light Switch at Home and How to Find the Cause
There is a dimmer in my hallway that hums. Not at full brightness and not when it is off, only in a band somewhere between a...
Living
Gurgling Drains in the Bathroom and How to Find the Cause
The bath in my sister's house makes a noise like someone swallowing, but only when the kitchen sink empties two rooms away.
Living
A Sticking Door and How to Find the Real Cause
There is a bedroom door in a 1930s flat I used to rent that fought me every November.