Washing Machine Not Draining and How to Find the Cause
The cycle ends, you open the door and there is still a pool of grey water sitting in the drum, or the machine stops mid-cycle with an error code and a full load of soaking clothes.

The cycle ends, you open the door and there is still a pool of grey water sitting in the drum, or the machine stops mid-cycle with an error code and a full load of soaking clothes. A washing machine not draining is one of the most common appliance faults, and in most homes it turns out to be something you can find and fix in under an hour with a towel, a tray and a torch.
The trick is to check the causes in order, from the cheapest and most likely to the least likely. Here is the sequence I use.
First, make it safe
Before touching anything, switch the machine off at the wall and unplug it. Turn off the cold and hot water taps behind it if you can reach them. Water and mains power do not mix, and you will be working near both.
Then get ready for water. A front loader can hold 5 to 15 litres when it fails to drain. Lay down old towels and find a shallow baking tray or roasting tin. A deep bucket will not fit under the filter on most machines.
Washing machine not draining: the five usual suspects
Almost every case comes down to one of these. They are listed roughly from most to least common.
| Cause | Typical sign | Fix difficulty |
|---|---|---|
| Blocked pump filter | Slow drain, humming noise, error code | Easy |
| Kinked or clogged drain hose | No drain, no unusual noise | Easy |
| Blocked sink trap or standpipe | Water backs up into sink or around pipe | Easy to moderate |
| Faulty drain pump | No sound from pump at all, or loud grinding | Moderate |
| Door lock or control fault | Error code, pump never starts | Technician |
Step 1: Clean the pump filter
On most front loaders, the filter sits behind a small flap at the bottom front corner. Some machines have a thin drain tube next to it. If yours does, pull it out, unplug the end over the tray and let the water out slowly. Empty the tray as often as you need to.
Once the flow stops, twist the filter cap anticlockwise and pull it out. Expect a smell. You will often find coins, hair grips, buttons, tissue fluff and the occasional sock. Rinse the filter under the tap, shine a torch into the opening and check that the small impeller blade behind it spins freely when you poke it with a finger.
Refit the filter firmly, plug in and run a rinse and spin cycle. In my experience this alone fixes around half of all drainage problems.
Top loaders are different
Many top loading machines have no user filter at all. If yours is one of them, skip straight to the hose and the plumbing below, and check the manual for a lint trap near the agitator.
Step 2: Check the drain hose
Pull the machine forward slowly, just enough to see behind it. Look for a hose that has been squashed flat against the wall or folded into a kink. That happens a lot after a machine is pushed back in following a repair or a house move.
Then disconnect the hose from the standpipe or sink connection and hold the end over your tray. Blow through it or run water from a jug through it. If it is blocked, a straightened wire coat hanger or a long bottle brush will usually clear the clog. Replacement hoses cost about 10 to 20 USD if the old one is cracked.
Check the hose height
The hose should loop up to between 60 and 90 cm from the floor before dropping into the standpipe. Too low, and water can siphon out during the wash. Too high, and a weak pump may struggle to lift it.
Step 3: Look at the house plumbing
If the hose is clear, the blockage may be in your pipes rather than the machine. Signs include water bubbling up around the standpipe or the kitchen sink gurgling when the washer drains.
- If the washer shares a trap with the kitchen sink, unscrew the trap and clear out grease and food waste.
- Pour a full kettle of hot (not boiling) water down the standpipe and watch how fast it drains. Slow drainage means the blockage is further along.
- A cheap plastic drain snake can reach 1 to 2 metres into the pipe.
A slow standpipe can also leak quietly into the wall over months. If you notice damp patches nearby, our guide to tracking down a hidden water leak at home explains how to confirm it.
Do not reach for drain cleaner first
A common suggestion online is to pour chemical drain cleaner into the drum or down the standpipe and run an empty cycle. I would avoid that. Strong caustic cleaners can damage rubber seals and the pump, and if the blockage is a solid object in the filter, no chemical will move it. You also end up with a filter compartment full of hazardous liquid that you then have to drain by hand.
Mechanical checks are cheaper, safer and tell you what actually caused the problem. A sock in the filter means you need a laundry bag for small items. Grease in the trap means you need to change what goes down the sink. A chemical fix tells you nothing.
Step 4: Listen to the pump
With the filter and hoses clear, start a spin only cycle and put your ear near the bottom of the machine. A healthy pump makes a steady hum with water rushing. Silence usually means the pump is not getting power or has failed. Loud grinding means something is caught in it or the bearings are worn.
Replacement drain pumps cost 25 to 60 USD for most brands and take an hour or two to swap if you are comfortable removing panels. If the pump hums but nothing moves, or the machine throws a door lock or control error, call a technician. The same step by step approach works for other appliance puzzles, like the ones in our guide on why a toilet keeps running and how to find the cause.
Preventing it next time
- Check pockets before every wash.
- Clean the pump filter every two to three months.
- Use the right amount of detergent. Too much creates excess suds that can trigger drain errors on some machines.
- Run a hot maintenance wash once a month. It also helps with musty odours, which we cover in tracking down a mystery smell at home.
Frequently asked questions
Why is there still water in my washing machine after the cycle?
The most common reason is a blocked pump filter, followed by a kinked or clogged drain hose. A small amount of water in the filter area is normal, but standing water in the drum is not. Check the filter first, then the hose.
How do I manually drain a washing machine?
Unplug the machine, place towels and a shallow tray under the bottom front corner, and open the filter flap. Use the small drain tube if your model has one, or slowly unscrew the filter cap to release the water in stages.
How much does it cost to fix a washing machine that will not drain?
If the cause is the filter or hose, it costs nothing or around 10 to 20 USD for a new hose. A new drain pump runs about 25 to 60 USD in parts. A technician call-out typically adds 80 to 150 USD depending on your area.
More in Living
Living
Buzzing Light Switch at Home and How to Find the Cause
There is a dimmer in my hallway that hums. Not at full brightness and not when it is off, only in a band somewhere between a...
Living
Gurgling Drains in the Bathroom and How to Find the Cause
The bath in my sister's house makes a noise like someone swallowing, but only when the kitchen sink empties two rooms away.
Living
A Sticking Door and How to Find the Real Cause
There is a bedroom door in a 1930s flat I used to rent that fought me every November.